Success Stories


Of about 350 species of earth worms in India with various food and burrowing habits, Eisenia fetida, Eudrilus eugeniae, Perionyx excavatius are some of the species for rearing to convert organic wastes into manure. The worms feed on any biodegradable matter ranging from coir waste to kitchen garbage and vermicomposting units are ideally suited to locations / units with generation of considerable quantities of organic wastes. One earthworm reaching reproductive age of about six weeks lays one egg capsule (containing 7 embryoes) every 7 - 10 days. Three to seven worms emerge out of each capsule. Thus, the multiplication of worms under optimum growth conditions is very fast. The worms live for about 2 years. Fully grown worms could be separated and dried in a oven to make 'worm meal' which is a rich source of protein (70%) for use in animal feed.
Suburbs of cities and villages around urban centres can be ideal locations for practice of vermicomposting on a large scale, from the view point of availability of raw material and marketing of the produce. As use of the compost is said to have ameliorative effect on product from fruit, flower and vegetable crops, vermicomposting units may be located in areas with concentration of fruit and vegetable growers and floriculture units.
As the wastes are pulverised as they pass through the worm, the surface area of the material increases which in turn helps as base for nutrients. Vermicompost, apart from supplying nutrients and growth enhancing harmones to plants, improves the soil structure leading to increase in water and nutrient holding capacities of soil. Chemical fertilizer in moderate doses can go along with vermicoposting.
For a vermi-composting unit, whether small or big, this is an essential item and is required for having the vermi beds. They could be of thatched roof supported by bamboo rafters and purlins, wooden trusses and stone pillars. If the size is so chosen as to prevent wetting of beds due to rain on a windy day, they could be open sheds. While designing the sheds adequate room has to be left around the beds for easy movement of the labour attending to the filling and harvesting the beds.
Normally the beds are 75 cm - 90 cm thick depending on the provision of filter for drainage of excess water. The entire bed area could be above the ground. Care should be taken to make the bed with uniform height over the entire width to the extent possible to avoid low production owing to low bed volumes. The bed width should not be more that 1.5 m to allow easy access to the centre of the bed.
About 0.5-1 acre of land will be needed to set up a vermiculture production cum extension centre. The centre will have at least 8-10 sheds each of about 180-200 sq.ft. It should also have a bore well, and pump set or watering arrangement and other equipments as described in the scheme economics. The land can be taken on lease of at least 10-15 years. Even sub marginal land also will serve the purpose.
When the activity is taken up on a large scale on commercial lines, considerable amount may have to be spent on buildings to house the office, store the raw material and finished product, provide minimum accommodation to the Manager and workers. The cost of the buildings along with the electrification of these buildings and the vermi-sheds may be included under this item.
Seed Stock
This is an important item requiring considerable investment. Though the worms multiply fast to give the required numbers over a period of 6 months to a year, it may not be wise to wait till such a time having invested on the infrastructure heavily. Thus, worms @ 350 worms per m3 of bed space should be adequate to start with and to build up the required population in about two cycles or three without unduly affecting the estimated production.
Fencing and Roads/Paths
The site area needs development for construction of structures and development of roads and pathways for easy movement of hand-drawn trolleys/wheel barrows for conveying the raw material and the finished products to and from the vermi-sheds. The entire area has to be fenced to prevent trespass by animals and other unwanted elements. These could be estimated based on the length of the periphery of the farm and the length and type of roads/paths required. The costs on fencing and formation of roads should be kept low as these investments are essential for a production unit, yet would not lead to increase in production.
Water Supply System
As the beds have always to be kept moist with about 50% moisture content, there is need to plan for a water source, lifting mechanism and a system of conveying and applying the water to the vermi-beds. Drippers with round the clock flow arrangement would be quite handy for continuous supply and saving on water. Such a water supply/application system requiring considerable initial investment, however, reduces the operational costs on hand watering and prove economical in the long run. The cost of these items depend on the capacity of the unit and the type of water supply chosen.
Farm machinery and implements are required for cutting (shredding) the raw material in small pieces, conveying shredded raw material to the vermi-sheds, loading, unloading, collection of compost, loosening of beds for aeration, shifting of the compost before packing and for air drying of the compost, automatic packing and stitching for efficient running of the unit. Costs of providing necessary implements and the machinery have to be included in the project cost.
For any vermi-composting unit transport arrangement is a must. When the source of raw material is away from the production unit, an off-site transport becomes major item of investment. A large sized unit with about 1000 tonnes per annum capacity may require a 3-tonne capacity mini-truck. With small units particularly with the availability of raw material near the site, expending on transport facility may become infructuous. On-site transport facilities like manually drawn trolleys to convey raw material and finished products between the storage point and the vermi-compost sheds could also be included in the project cost.
A reasonable amount could also be considered for furnishing the office-cum-stores including the storage racks and other office equipment. These enhance the efficiency of operations.
Operational Costs
In order to operate the unit, expenditure on some items have to be incurred on a recurring basis. These items include salaries of the staff, wages to the labourers, cost of raw material, fuel cost on transport of raw materials and finished goods, packing material cost, repairs and maintenance, power, insurance, etc. The number of office personnel and labourers have to be decided breaking each activity into a number of sub-activities and for each sub-activity estimating the work involved and the capacity of the labour to finish the work in a given time. The number of persons should be so chosen to keep them engaged throughout by providing enough persons at various work points like stores, vermi-beds and equipping them with adequate number of implements to avoid undue waiting.